Напівпричіп з робочою платформою

KÖGEL Multi Chassis, verstärkt, Bordwände

You can find our complete vehicle inventory with vehicles available immediately and in the short term on our website.

Excerpt from the equipment. Complete equipment available upon request.

Chassis
* Regular ladder frame in lightweight steel with continuous crossmembers
* With an extension of the chassis frame, the coupling plate is approximately 8 mm thick
* with a 2-inch kingpin according to DIN 74080 / ISO 337

Suspension
* Axle lift mechanism on axle 1
* Three-axle unit SAF INTRADISC
* with disc brakes Ø 430 mm
* ET 120 air suspension with approximately 180 mm travel

Tires
* Wheels with internal sensors according to UN ECE R141
* 6x 385/65 R 22.5 UNIROYAL TH 50
* 6 steel rims 22.5 x 11.75
* Offset approximately 120 mm (ET 120)

Chassis components
* Mechanical fifth wheel with leveling foot, approximately 24 t lifting capacity, single-sided operation on the right-hand side while driving
* Storage box for: 10 side panels, folding stakes, and rear gate, fully enclosed, protected against spray water, also serves as a side protection device
* 2 plastic toolboxes, waterproof, dimensions (internal) approximately 545 x 400 x 400 mm, installed at the rear, 1x on the left and 1x on the right

Brake / Air suspension system
* EBS system 2S/2M with stability program (includes ABS/ALB function)
* EBS plug connection ISO 7638 (without connection lines)
* Parking brake as a spring brake, external pneumatic connections as well as an external EBS diagnostic connection via ISO 7638 plug connection
* WABCO EBS system
* Air suspension system including 1 lifting and lowering valve, mounted on the left-hand side behind the axle unit while driving, driving position is set automatically
* 2 non-interchangeable coupling heads at the front ISO 1728
* Air tanks for the brake system and air reservoir made of steel (EN 286-2)
Floor
* Flat floor approximately 30 mm thick, multiply laminated plywood
* Floor sealed around the perimeter
* Stake pockets for square tube inserts approximately 80 x 80 mm
* Storage for a maximum of 14 square tube inserts approximately 80 x 80 (length 1,990 mm) on the front wall inside

Front wall
* Front wall approximately 2,000 mm high with steel corner posts, with profiled steel sheet, screwed/riveted to the frame
* 2 pairs of lashing points (permissible lashing force approximately 1,000 kg per ring) on the front wall according to EN 12640, Note: If the front wall is used for securing the load, suitable lashing straps must be used to tighten the load, if the vehicle is operated without side panels and a rear gate

Rear wall
* Folding rear wall approximately 600 mm made of aluminum hollow profiles with 3 tension bars and T-handle locks
* 2 folding steps on the inside, folding steel corner posts at the rear in the height of the side panels

Side wall
* 4 pairs of folding stakes in the height of the side panels
Iiedpfozc A Afex Am Rod
* VarioFix steel hole outer frame
* 4 pairs of stake holders for folding stakes on the outer frame (evenly distributed)
* 24 pairs of lashing eyes in the outer frame (according to EN 12640), permissible tensile force approximately 5,000 kg per ring

Side panels
* 5 pairs of folding side panels approximately 600 mm made of aluminum hollow profiles with tension bars

Electrical / Electronics
* Lamp carrier made of steel, arranged above the underrun protection
* KÖGEL LUXIMA Premium package, consisting of: LED license plate lighting, LED outline lights and reflectors at the front, flashing LED side marker lights, Superseal and bayon

Оголошення було перекладено автоматично. Можливі помилки перекладу.